Car wax (Light colours)
Soul carnauba car wax, by Auto Finesse, lets your vehicle’s natural beauty shine through.
The Auto Finesse Soul carnauba car wax's highly-reflective visual dynamics and glass-like finish makes it especially well-suited to light, bright colours. Even the palest hues burst into life with a natural glossy glow.
Soul contains 33% T1 Grade Brazilian Carnauba Wax by volume, with the remainder being made up by all natural Beeswax, Candelilla wax, and oils, protecting against nature’s elements, giving it water repellency, and resistance to environmental pollution (Including UV-fading, acid rain, and bird droppings.).
With its sweet mango scent, Soul is capable of providing up to 3-months of durable protection on a daily driver.
Before getting your ‘wax on’, the vehicle must be clean. A clay bar can be used to remove any bonded contamination such as tar. If paintwork hasn’t seen a polish in the last 6-12 month, it’s wise to prep the surface with a pre-wax cleanser. Turn a foam applicator half a turn in the wax tub, this should be enough to coat a complete panel. Apply sparingly in small even strokes.
Once one panel is complete, move onto the next. Buff off the first panel when you’ve completely coated the second panel. If wax has dried, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied,) you can use a water-based quick detailer to help ease removal of the residue.
It’s important to wait at least 3 hours in between coats or layers of wax.
Do not wax the vehicle if temperature is below 6 degrees Celsius, or above 25 degrees Celsius. Waxing in direct sunlight, or conditions of high humidity can lead to over, or under-curing of the product before removal.
Directions for use
We've put together a few simple steps to help you get the best out of Soul 150g highlighting what you should be doing to get the most out of Soul 150g when detailing your pride and joy.
- Before waxing, make sure that the vehicle is clean, and cool to the touch. If bonded contamination is present, use a Clay Bar to prep the surface for best results. If the paintwork is lightly marred, or the vehicle has not been polished in the last 6-12 months, it is also advisable to use one of our signature Pre-Wax Cleansers in order to create the maximum shine.
- Place an Auto Finesse Waxmate foam applicator inside the pot of wax, and rotate it half a turn to prime the pad with product. This is typically enough wax to protect a single moderately-sized panel, though this may vary depending upon the condition of the paintwork.
- Apply the wax to the panel with small, overlapping circular strokes, light pressure, and in a consistent pattern to obtain full coverage of the paint. If the applicator feels like it is starting to run dry across the surface, or coverage becomes uneven, return the applicator to the container using another quarter-turn of the pad to re-prime the foam.
- The goal when waxing is to apply the product as thinly and evenly as possible, since a little bit goes a very long way to protecting and enhancing the shine of your vehicle.
- Once you have completed one normal-sized panel, or half of a large one, move on to another section of equal size. When you are done waxing the second section, you will be ready to buff off the wax from the first using a plush Microfiber Towel. Alternating in between buffing and waxing panels until the vehicle is fully protected allows you to maintain the ideal curing times for the wax, and makes for very easy removal of the remaining residue.
- Auto Finesse Soul only takes a few minutes to cure, so take care not to let the product dry onto the surface. If the wax has been allowed to dry, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied.), you can use a water-based QD like Auto Finesse Finale to help ease removal of the residue.
- When applying multiple layers of wax for extra depth, wetness, and protection, make sure to wait at least 3-hours in between coats to allow the organic solvents to fully flash.
- Do not wax the vehicle if the ambient temperature is below Approximately 6-degrees Celsius, or above 25-Degrees Celsius.
- Waxing in direct sunlight, or conditions of high humidity can respectively lead to over, or under-curing of the product before removal.